A ceramic PCB supplier audit checklist is a structured scoring tool that covers material traceability, process capability, quality systems, and shipping controls specific to ceramic substrates. Use it during on-site visits or remote document reviews to compare vendors on the same scale and catch gaps before they become field failures.
Ceramic boards carry higher piece costs than FR-4, and rework is often impossible because the substrate is brittle. A defective lot of 96% alumina ceramic PCBs cannot be stripped and re-etched the way an organic board can. That makes supplier qualification more consequential here than in standard PCB sourcing.
The downloadable checklist is organized into seven audit sections. Each section contains specific line items scored on a 0-1-2 scale (non-conforming / partial / conforming). The sections are:

Most PCB supplier audit templates are written for organic boards. Ceramic fabrication introduces failure modes that those templates miss entirely. The items below deserve extra scrutiny.
A ceramic PCB factory that does not inspect incoming blanks is gambling on its substrate vendor’s quality. Ask to see records for camber (per ASTM C1161 or internal spec), surface roughness (Ra), and fired density. For aluminum nitride substrates, confirm that thermal conductivity is verified per lot, not assumed from a generic datasheet. AlN conductivity can range from 150 to 230 W/mK depending on the powder source and sintering profile.
Copper adhesion to a ceramic surface is the single most common field-failure root cause in ceramic PCBs. The audit should confirm the factory runs peel-strength or pull-test sampling per lot. Acceptable values depend on the process:
| Metallization process | Typical peel strength | Test method |
|---|---|---|
| DBC (direct bonded copper) | ≥ 4 N/mm | 90° peel, IPC-TM-650 2.4.8 |
| DPC (direct plated copper) | ≥ 0.8 N/mm (thin Cu) | 90° peel, IPC-TM-650 2.4.8 |
| AMB (active metal braze) | ≥ 6 N/mm | 90° peel per manufacturer spec |
| Thick film (Ag/Pd, Au) | ≥ 20 N (pull test) | MIL-STD-883, Method 2011 |
Typical values for commercially available processes, for comparison only. Confirm against the datasheet for your specific grade.
Ceramic substrates themselves tolerate extreme temperatures, but the ceramic-metal interface does not survive unlimited thermal cycling. Ask whether the supplier runs thermal shock testing (e.g., −40 °C to +150 °C, 1000 cycles per JEDEC JESD22-A104) on a sampling basis. If they do not, you are the reliability test.
Fired ceramic shrinks during sintering (HTCC/LTCC) or is cut to size after firing. Either way, dimensional control matters for assembly fit. Verify that the factory measures and records positional tolerance on metallization features, not just outline dimensions. For a DFM-compliant ceramic design, the supplier should be able to hold ±50 µm on feature placement for DPC and ±75–100 µm for thick film.
Each line item scores 0, 1, or 2. A zero on any safety or traceability item is an automatic fail regardless of total score. For the remaining items, calculate a percentage:
Document the scoring in writing and share it with the supplier. A good factory will welcome the feedback. A factory that objects to a structured audit is telling you something important.
Travel budgets are finite. A remote audit is not as thorough as walking the floor, but it still catches the majority of disqualifying issues. Here is a practical approach:
If the supplier holds UL certification for ceramic boards, ask for the UL file number and verify it on UL’s online database. A valid UL listing means the factory has already passed a third-party process audit, which covers some of the same ground.

This checklist is designed for ceramic PCB fabrication. It does not cover SMT assembly, wire bonding, or module-level packaging. If your supplier also assembles components onto the ceramic board, you need a separate assembly audit that covers solder paste inspection, reflow profiling, and X-ray for void analysis. The metallization audit items here also do not apply to standard FR-4 or metal-core PCB suppliers, which have different failure modes and different relevant standards (IPC-6012 Class 2/3 for rigid organic boards).
An audit works best when the supplier already has your technical requirements in hand. Before scheduling a factory visit, send a complete ceramic PCB RFQ package that specifies the substrate material, metallization process, copper thickness, surface finish, and acceptance criteria. This lets the supplier show you exactly how they would build your part, rather than giving generic answers.
Re-audit annually for high-reliability applications (medical, automotive, aerospace) and every two years for commercial/industrial. Trigger an unscheduled re-audit if you see a spike in incoming quality issues or if the supplier changes a key process.
An ISO 9001 audit confirms that a quality management system exists, but it does not check ceramic-specific process controls like substrate incoming inspection or metallization adhesion testing. Use the ISO certificate as a baseline and layer this ceramic-specific checklist on top.
That is a red flag. A supplier that tracks critical dimensions with SPC should be willing to share trend charts with customer-identifying information removed. If they claim not to use SPC at all, score that section as zero and weigh the risk accordingly.
Ideally, yes. The ceramic substrate material is the foundation of every board. At minimum, verify that your PCB supplier has a formal qualification process for their substrate vendors and can show you incoming inspection data by lot.
IATF 16949 does not prohibit remote audits, but most automotive OEMs require at least one on-site visit during initial supplier qualification. A remote audit can serve as the preliminary screen. Plan an on-site visit before granting full production approval.